HOW TO REPLACE A TUB (FOR BEGINNERS).

How To Replace A Tub (For Beginners).

How To Replace A Tub (For Beginners).

Blog Article

Get Estimate

What're your ideas concerning How to Install a Bathtub?


How to Install a Bathtub
Setting up a bath tub isn't specifically brain surgery, yet it does call for strong plumbing, woodworking, as well as occasionally, tiling abilities. Changing an old bath tub with a brand-new one is additionally a reasonably hard task. If the old bathtub is conveniently accessible, the project can move speedily; if you have to open a wall to remove the old tub and also place the brand-new bath tub, the job is a lot harder. In either situation, the job is within a house handyman's abilities, although you will require an assistant to vacate the old bathtub as well as embeded in the new one. Ensure you have qualified yourself for the task as well as are comfortable trying it. As opposed to working with a specialist to take control of a halfway-completed job, it is much better to consider employing one prior to you begin. Chances are you might require an expert plumber to make tube links.
This write-up will certainly assist you set up a brand-new tub in your restroom if you have already bought a new bathtub and also don't need to change the setup of your previous water pipelines.
Your devices as well as material checklist ought to consist of the following:
  • New Bathtub

  • Hammer

  • Pipe Wrenches

  • Prybar

  • Shatterproof glass

  • Degree

  • Pliers

  • Adjustable Wrench

  • Putty Knife

  • Screwdriver

  • Cold Chisel

  • Tape Measure

  • Pipeline Caps


  • Removing Old Touches


    If you need to replace old faucets with brand-new ones as a part of your setup, then the first thing you should do is disconnect the water. After doing so, activate the taps to drain pipes any type of water remaining in the system. The procedure of eliminating the existing taps can be fairly troublesome due to the limited access that is usually the situation.
    Use a container wrench (crowsfoot spanner) or a faucet device to undo the nut that links the supply pipes to the faucets. Have a cloth all set for the staying water that will originate from the pipes. When the supply pipelines have been gotten rid of, utilize the very same tool to loosen up the nut that holds the taps onto the bath/basin. You will certainly need to quit the single faucets from turning throughout this process. As soon as the taps have actually been removed, the holes in the bath/basin will need to be cleaned up of any kind of old securing compound.
    Prior to proceeding to fit the brand-new taps, contrast the pipeline connections on the old faucets to the new faucets. If the old taps are longer than the brand-new taps, after that a shank adapter is required for the brand-new taps to fit.

    Suitable New Taps


    If the tails of the brand-new taps are plastic, after that you will require a plastic port to avoid damages to the thread. One end of the adapter fits on the plastic tail of the tap and also the various other end supplies a connection to the existing supply pipelines.
    If you need to fit a monobloc, after that you will call for decreasing couplers, which links the 10mm pipeline of the monobloc to the conventional 15mm supply pipeline.
    Next, position the tap in the installing opening in the bath/basin guaranteeing that the washing machines are in place in between the faucet and the sink. Protect the faucet in place with the producer supplied backnut. As soon as the tap is safely in position, the supply pipelines can be attached to the tails of the taps. The taps can either be linked by utilizing corrugated copper piping or with regular tap connectors. The previous kind needs to be connected to the tap finishes initially, tightening up just by hand. The supply pipes can later be linked to the various other end. Tighten up both ends with a spanner after both ends have been connected.

    Setting up the Tub


    Making use of both wood boards under its feet, put the bath tub in the called for position. The wooden boards are valuable in uniformly spreading out the weight of the bath tub over the location of the boards instead of focusing all the weight onto four small points.
    The next objective is to make sure that the bath tub is leveled all round. This can be attained by examining the level and adjusting the feet on the bathtub until the spirit level reviews degree.
    To mount faucets, fit all-time low of the outermost flexible tap connector to the appropriate supply pipe by making a compression join; then do the same for the other tap.
    Switch on the water supply and check all joints and also brand-new pipework for leakages and also tighten them if essential. Load the bath tub as well as additionally inspect the overflow electrical outlet as well as the typical electrical outlet for leakages.
    Lastly, repair the bath paneling as described in the supplier's user's manual. Tiling as well as sealing around the bath tub needs to wait up until the bathtub has actually been made use of at least when as this will certainly settle it right into its last setting.

    Preparing for the Installment


    To start with, the supporting frame provided with the bath should be fitted (if called for) according to the maker's guidelines. Next off, fit the taps or mixer to the bath tub. When suitable the faucet block, it is necessary to make sure that if the tap comes with a plastic washing machine, it is fitted between the bath and also the taps. On a plastic bathroom, it is likewise sensible to fit a sustaining plate under the faucets unit to prevent pressure on the tub.
    Fit the flexible faucet ports to the bottom of the two faucets utilizing 2 nuts and olives (often supplied with the bathtub). Fit the plug-hole outlet by smearing mastic filler round the sink electrical outlet hole, and afterwards pass the electrical outlet through the hole in the bathroom. Utilize the nut supplied by the supplier to fit the plug-hole. Analyze the plug-hole outlet for an inlet on the side for the overflow pipeline.
    Next, fit the end of the flexible overflow pipeline to the overflow outlet. Afterwards, screw the pipe to the overflow face which need to be fitted inside the bath. Make sure you utilize all of the provided washers.
    Attach the trap to the bottom of the waste electrical outlet on the tub by winding the thread of the waste outlet with silicone mastic or PTFE tape, and also screw on the trap to the electrical outlet. Link the bottom of the overflow tube in a comparable manner.The bath should currently be ready to be fitted in its final setting.

    Tiling Around the Bathtub


    In the location where the bath fulfills the tile, it is essential to seal the joins with a silicone rubber caulking. This is very important as the fitting can relocate enough to fracture a stiff seal, creating the water to permeate the wall surface in between the bath as well as the tiling, leading to issues with dampness and also possible leaks to the ceiling listed below.
    You can choose from a selection of coloured sealants to assimilate your fixtures and also fittings. They are offered in tubes as well as cartridges, and can securing spaces approximately a width of 3mm (1/8 inch). If you have a bigger gap to fill up, you can fill it with twists of drenched newspaper or soft rope. Bear in mind to always fill up the bathtub with water before securing, to allow for the motion experienced when the bathtub is in usage. The sealant can split fairly early if you do not think about this movement prior to securing.
    Additionally, ceramic coving or quadrant ceramic tiles can be made use of to border the bath or shower tray. Plastic strips of coving, which are easy to use as well as reduce to dimension, are also easily offered on the marketplace. It is suggested to fit the tiles using water-resistant or water resistant glue and grout.

    How to Install or Replace a Bathtub


    Find Your Dimensions


    The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.



    After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?


    Disconnect the Water Supply and Drain Assembly


    Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.



    Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.



    Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.


    Cut Out the Old Tub


    After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.



    Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.



    Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.


    Install the New Tub


    Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.



    Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.



    Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.



    When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.


    Secure the Tub


    After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.



    Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.



    Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.



    Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.

    https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/


    Tools You Need to Install a New Bathtub

    Do you appreciate reading up on How to Install a Bathtub: Install an Acrylic Tub and Tub Surround? Put a remark down the page. We'd be delighted to listen to your opinion about this blog posting. We are looking forward to see you back again in the future. Don't hesitate to take a moment to promote this post if you enjoyed it. Thank you so much for taking the time to read it.



    Get Estimate

    Report this page